Screens & video
Two big TVs up front and a confidence monitor, with SDI video from the balcony booth — plus a new SDI run to the nursery so they can stream the service there.
Equipment arrived · outlet boxes bought
All the equipment except the TVs has arrived (ordered 10/28 on Amazon). The coax was bought at Lowe's 10/28 and is at the church. Micheal got the 2 outlet boxes 11/2. Still to buy locally: exterior silicone. Micheal is buying the coax crimper and stripper himself.
Next steps
- To doPut in 2 regular outlets in the wall behind the front TVs
- To doBuy the TVs (2 front TVs + 65″ confidence monitor)
- In progressRun additional SDI (coax) to the nursery so they can stream the service
- In progressPull power for the nursery SDI feed and behind the stage
Done (3)
- ✓DonePick up coax and Cat6 at Lowe's in Corinth
- ✓DoneRoute the coax and Cat6e cable from the booth to the TVs
- ✓DoneRSM team: order the equipment (everything but the TVs)
Two big TVs on the front wall, one each side of the baptistry, plus a 65″ confidence monitor on the front of the balcony facing the stage. The temporary sound booth is a table in the back-right corner of the balcony. Front video goes from the booth computer over SDI on coax (no delay to fight). The route: found a way to run it inside the same wall the whole way, from the booth to the TVs — no longer goes outside or depends on the soffit being open. One coax and one Cat6e network cable run together. Also running an additional SDI feed out to the nursery so they can stream the service there, with its own power pull — same inside-the-wall approach, using attic space instead of the soffit.









How the video gets to the TVs
Still to buy: the front TVs
The 2 front TVs (and the 65″ confidence monitor) still need to be bought. Everything they plug into is in the equipment proposal, so the TVs can be bought whenever the church is ready. Tap a TV to see the full project cost. TV prices were checked Oct 16, 2026; the Sam's Club sale ended Oct 18, so recheck before buying (membership needed for Sam's). Amazon links use Micheal's affiliate tag.
Front TVs (×2): tap one
Confidence monitor (×1)
| Item | Qty | Price | Buy | Notes |
|---|---|---|---|---|
| Confidence monitor (back) | ||||
| Hisense 65″ A6 4K TV 65A6H | 1 | $509.86 | Mounted on the front of the balcony, facing the stage, so whoever is up front can see the slides and notes (stage display). In stock on Amazon as of Oct 16. Sam's may be cheaper in club. | |
Equipment proposal: $695.48
Everything except the TVs, waiting on the RSM team to order (one-click cart link at the top). Silicone and the 2 outlet boxes come from a local hardware store.
| Item | Qty | Price | Buy | Notes |
|---|---|---|---|---|
| Wall mounts | ||||
| Heavy Duty Fixed (flat) Low-Profile TV Wall Mount, 55–120″ Ultra slim fixed, VESA up to 900×600 | 2 | $37.99 = $75.98 | Micheal's pick for the front TVs. Flat, one-piece, holds 220 lb (the 98″ TVs are about 100–120 lb), VESA up to 900×600, fits 16/24/32″ studs, safety lock. In stock. | |
| Confidence monitor (back) | ||||
| PERLESMITH tilting wall mount, 37–85″ PSLTK1 | 1 | $18.96 | For the 65″. Holds 132 lb. In stock. | |
| BlueRigger 35 ft in-wall HDMI (CL3) 35 ft | 1 | $39.99 | Booth computer's second output to the 65″. Measure; a shorter one is fine if it's close. | |
| Video converters | ||||
| Blackmagic Micro Converter HDMI to SDI 3G (with power supply) CONVCMIC/HS03G/WPSU | 1 | $85.00 | At the booth. AC adapter included. In stock. | |
| Blackmagic Micro Converter SDI to HDMI 3G (no power supply) CONVCMIC/SH03G | 1 | $75.00 | The version with a power supply wasn't available. Powered by USB-C: runs on the spare's power supply, or any USB-C phone charger. | |
| Blackmagic BiDirectional SDI/HDMI 3G (with power supply): SPARE CONVBDC/SDI/HDMI03G/PS | 1 | $99.00 | Converts both ways, so it can replace either converter if one fails. Its power supply runs the SDI-to-HDMI unit; whichever unit fails frees its power supply for the spare. | |
| HDMI | ||||
| OREI UltraHD 1×2 HDMI splitter (4K60) UHDS-102C | 1 | $18.90 | Sits with the SDI-to-HDMI converter in the middle of the wall behind the stage, so both 35 ft HDMI runs are even. | |
| BlueRigger 35 ft in-wall HDMI (CL3) 35 ft | 2 | $39.99 = $79.98 | Splitter (middle of the wall behind the stage) to each front TV: about 20 studs (~27 ft), around a small corner and up to the TV, with slack. | |
| Highwings HDMI 2.1 cable, 2-pack (8–10 ft) 2-pack | 1 | $14.00 (est.) | One at the booth (computer → HDMI-to-SDI converter), one behind the stage (SDI-to-HDMI converter → splitter). Pick the length on the listing. | |
| SDI cable (outside run) | ||||
| Southwire RG6 Quad Shield coax, 500 ft, black (Lowe's item 3332782) Southwire RG6 Quad Shield | 1 | $71.68 | Micheal is picking this up at Lowe's in Corinth (faster than Amazon). One run to the TVs, about 150-200 ft, with plenty left over. | |
| Klein BNC compression connectors for RG6, 10-pack VDV813-607 | 1 | $29.99 | 2 needed (one each end) plus spares for mistakes. Keep the connectors indoors. | |
| QCSIW white self-closing braided cable sleeve, 1/2 in, 10 ft 4 packs = 40 ft | 4 | $9.00 (est.) = $36.00 | Makes the black coax (and the Cat6 beside it) white where it shows indoors. Wraps on from the side, so it can go on after crimping. | |
| Gardner Bender masonry coax clips, 100-pack, black UV PCS-100B | 1 | $9.00 | Nail into the mortar joints about every 2–3 ft (if not tucked in the soffit). One pack covers the run. | |
| Exterior silicone GE Silicone 2 | 1 | $10.00 (est.) | — | Seal the holes where the coax goes through the walls. |
| Wall openings | ||||
| XIOGZAXI desk grommets, 2 in, white, 10-pack with 2 in hole saw 2 in / 50 mm | 1 | $12.00 (est.) | Hole saw included. Cut 2 in holes behind each TV and at the splitter behind the stage; snap a grommet in each. A dab of caulk holds them in drywall. | |
| Power | ||||
| Regular wall outlet + box + cover plate (behind each front TV) 15A duplex, old-work box | 2 | $10.00 (est.) = $20.00 | — | Tied into the existing circuit already run backstage. Rayburn installs, through the attic. |
Other options and alternatives
| Item | Qty | Price | Buy | Notes |
|---|---|---|---|---|
| Wall mounts | ||||
| HOME VISION Heavy Duty Fixed (flat) TV Wall Mount, 48–120″ Fixed, low profile | 2 | $55.99 = $111.98 | Option: flat, holds 264 lb (more than needed), VESA up to 800×600. In stock. | |
| USX MOUNT Heavy Duty Tilting TV Wall Mount, 60–120″ Tilt ± | 2 | $51.99 = $103.98 | Option: even cheaper and tilts down toward the pews. Holds 220 lb, VESA up to 900×600. In stock. | |
| monTEK Heavy Duty Tilting TV Wall Mount, 60–120″ Tilt ±10° | 2 | $64.99 = $129.98 | Option: tilting, holds 300 lb, VESA up to 900×600. In stock. | |
| USX STAR Full Motion (swivel) TV Wall Mount, 60–120″ (UL listed) Swivel ±65°, tilt ±10°, 28″ extension | 2 | $99.99 = $199.98 | Option (Micheal's find): full motion, so each TV can swing in toward the center pews and tilt down. Holds 220 lb, VESA up to 900×600, works on studs or solid brick. In stock. | |
| SDI cable (outside run) | ||||
| 3-in-1 compression tool (BNC / RCA / F) Compression crimper | 1 | $25.95 | Not needed: Micheal is buying a Klein VDV211-063 crimper himself. | |
| Wireless option (instead of the coax run) | ||||
| Lemorele wireless HDMI kit, 1 transmitter + 2 receivers 1TX+2RX, 1080p60, 5 GHz | 1 | $119.99 | Micheal tested one from the balcony and it worked well. Replaces the converters, coax, splitter and the two 35 ft HDMI runs. Lemorele lists about 50 ms delay; test with a full room and with the WiFi on before relying on it. Price is what Micheal paid; check the listing. | |
Install notes
- Measure the real route: booth corner → along the top of the right wall → out where the ceiling drops → under the eave to the corner → along the wing's eave to the back door → inside to the converter. Add 15%. 3G-SDI is good to about 328 ft on RG6, and the 500 ft spool covers both runs.
- Outside: keep the coax tight under the eave, clipped every 2–3 ft (into the mortar joint at the top course or the fascia board). Drill the wall holes sloping slightly down toward the outside, leave a drip loop before each hole, and seal with silicone. Put the BNC connectors on indoors. Run the coax and the Cat6e together (one of each). Plan: have both cables ready before the soffit crew starts, so they go up inside the new soffit instead of being clipped under it.
- Set the computer to 1080p60. The Blackmagic converters and the splitter need no setup. Label every cable at both ends.
- Mount with two people, into studs. Center the TVs about 60–72″ above the platform, tilted down if they're high. Check the TV warranty: consumer warranties often exclude commercial or church use.
- The confidence monitor mounts on the front of the balcony, centered and facing the stage. It runs off the booth computer's second video output (stage display in your presentation software) with the 35 ft HDMI along the balcony floor, so it doesn't need SDI.
Unlisted working page (not in the site menu). Updated 2026-10-26.
